Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Garland
Gate parts and welding in Garland usually come down to one thing: a post that’s moved or a hinge that’s given up. A typical hinge replacement in Garland runs $145-$285 depending on the gate’s weight and whether the post needs shimming. Post reset work runs $325-$600 when the clay has pushed things out of plumb. We’re in Garland weekly, and we answer the phone at (903) 627-2906 around the clock. If your gate drags, binds, or won’t latch, call us. We’ll tell you straight what’s wrong and what it costs before a single bolt gets turned.
Why Ironworks Gate Co. Is Garland’s Preferred Gate Parts & Welding Company
Garland homeowners call us because we’ve been welding and hanging gates for over 42 years, and our Gate Parts & Welding crews know this city’s soil better than most. The Blackland Prairie clay under Garland swells when it’s wet and shrinks when it’s dry, and that cycle works on gate posts year after year. Homeowners in established neighborhoods like Camelot, Brentwood Place, and the streets off Broadway Boulevard have dealt with this for decades. A hinge swap alone won’t fix what the clay has moved.
Victor Salinas leads our crews, and he’s the one who set the standard we work to: check the post before touching the hinge. That’s not a slogan. It’s the difference between a repair that lasts and a callback six months later. Our Garland customers tell us the same thing over and over: the gate finally closes square, and it stays that way through the next wet season. We’re background-checked, uniformed, and we show up when we say we will. Every job ends with our written 90-Day Done Right Promise. If it’s not right, we come back. No arguing, no paperwork war.
Our Gate Parts & Welding Services in Garland
Hinge Replacement
Garland’s 1960s through 1980s tract homes were built with wood privacy gates hung on thin strap hinges, and 40 years of wind and clay movement have done their work. When a hinge wears or the post shifts, the gate drops at the latch side and starts scraping the ground. We replace hinges with heavier-gauge hardware sized for the gate, not just whatever fits the old screw holes. On solid infill gates that catch full north Texas wind, we often step up to adjustable hinges so the gate can be trued up later without pulling the post.
Post Replacement
Most post failures in Garland aren’t rot at the top. They’re movement at the base. The original posts on older suburban homes were set in shallow concrete that the expansive clay has cracked and tilted over decades. We dig out the old footing, set a new galvanized or powder-coated post in deeper concrete, and brace everything plumb before hanging the gate back. In south Garland around Duck Creek and east toward IH-30, we regularly pull posts that have walked two to three inches out of level. A new post set right ends the sag for good.
Rail Repair
The horizontal rails on a wood privacy gate take the brunt of wind load, and on gates that face open exposure such as the wide lots along Brand Road or down toward the lake, rail ends split where they meet the stiles. We reinforce split rails with steel mending plates, replace rotted sections, and when a gate’s structure is too far gone, we fabricate new rails and weld a steel frame behind the wood. You keep the look you’ve had for 30 years. The gate just stops falling apart.
Custom Welding
Some gate problems can’t be bought off a shelf. Cracked welds on steel frame gates, broken operator arms, a custom latch bracket that no supplier stocks. We weld on site in Garland, and we fabricate what’s needed. Victor Salinas has spent years welding gate steel in North Texas, and the work holds up to the heat, the wind, and the next hard freeze. If a previous repair failed at the weld point, we grind it back and do it properly. No shortcut passes for looks.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Garland
We service gate automation from LiftMaster, Mighty Mule, FAAC, and BFT, among nine brands we’re trained and equipped on. That matters in Garland because so many automatic gates here are retrofits on older wood gates, and the mix of opener brands on the ground is all over the map. We keep common parts and weld repairs moving fast so you don’t wait a week on a shipped part when a broken operator arm has your gate stuck halfway open. We quote the repair before the work starts, and we honor that quote.
Common Gate Parts & Welding Problems We See in Garland Homes
- Walking gates from clay heave. Garland sits on Blackland Prairie clay that swells and shrinks with moisture. Over several wet-dry cycles, a gate’s hinge-side and latch-side posts move at different rates, and the gate hangs visibly lopsided. Locals call it a walking gate. The fix starts with resetting the post, not swapping hinges.
- Wind-bent hinge posts on solid infill gates. Garland gets serious spring storm winds, and a solid wood gate catches all of it. Posts that looked fine for years suddenly lean, and the gate swings wild or won’t close at all. We reset and brace the post, then re-hang the gate square.
- Broken operator arms after freezes. The 2021 ice storm taught Garland homeowners what a hard freeze does to gate automation. Grease turns to glue, motors strain, and the arm or weld joints crack. After a freeze, we see a spike in calls from the neighborhoods around Firewheel and down Naaman School Road.
- Latch failures from sag-induced misalignment. A sagging gate drags the latch bolt out of line with the strike plate. People force the latch, and eventually the internal spring or the handle itself breaks. We fix the alignment first, then replace the latch, so you’re not back in the same spot next season.
Pricing for Gate Parts & Welding in Garland, TX
Here are the numbers we quote most often in Garland. Hinge replacement typically runs $145-$285 per gate, depending on weight and how far the post has moved. Post reset and re-set runs $325-$600, with welded steel reinforcement adding $75-$150 when the post needs it. Rail repair with steel mending plates runs $180-$350. Custom welding for operator arms or frame repairs runs $160-$420, quoted by the hour plus materials. Every price is agreed before work starts. No surprises on the bill. Call (903) 627-2906 for a free estimate, and ask about our $50 Off Any Repair Over $250 offer if your job qualifies. Seniors and veterans always get 5% off.
We Also Serve Cities Near Garland
Our Gate Parts & Welding in Garland crews also cover Sachse, Rowlett, Richardson, and Plano. If you’re just outside city limits, call (903) 627-2906 and we’ll get you on the schedule. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, with crews serving Garland locally every week.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Garland
Because the post is moving, not the hinge. Garland’s expansive clay swells and shrinks with every wet and dry spell, and over years it pushes gate posts out of plumb by inches. New hinges on a tilted post will sag again within a season or two. The lasting fix is a post reset, then re-hanging the gate. Call (903) 627-2906 and we’ll check the post differential first, before anything else gets touched.
First, find the manual release on your opener. Most LiftMaster, FAAC, and Mighty Mule models have a pull handle or keyed release near the operator. Pull it and the gate swings free by hand. Do not force the gate without disengaging the operator. Forcing it bends the rack or breaks the weld joints on the arm, and that turns a power outage into a $350 repair. If you can’t find the release or the gate won’t budge, call us at (903) 627-2906 and we’ll walk you through it.
Sometimes, but not always. If the break is at a clean weld point on a steel arm, we can grind it back and reweld it, usually for $160-$250. If the arm is cast aluminum or the break runs through a machined mount, welding will fail again. We’ll tell you the truth either way. We’d rather quote a replacement part than weld something that gives out during the next hard freeze. Estimates are free.
Yes. That’s exactly the job we do most in Garland. We dig out the old shallow footing, set a new post in deeper concrete, brace it plumb, and re-hang the gate with new hinges if the old ones are wallowed out. After a 2021-style hard freeze, we reset a heaved hinge post on a 6-foot cedar swing gate in a south Garland tract home, replaced cracked weld points on the operator arm, and re-hung the gate so the latch finally cleared by 2 inches. That gate is still square. The 90-Day Done Right Promise covers every reset we do.
We’re trained and equipped on nine major brands, and we keep common parts for LiftMaster, Mighty Mule, FAAC, and BFT on hand, plus we can source the rest quickly from our DFW suppliers. That means most Garland repairs get done in one visit. If your opener is from a brand we don’t recognize, call anyway. We’ll identify it and tell you what it needs. A live person answers at (903) 627-2906, 24 hours a day, seven days a week.
If your gate is dragging, sagging, flapping in the wind, or stuck shut after a storm, call (903) 627-2906. We serve Garland and the surrounding cities with free estimates, upfront pricing, and the written 90-Day Done Right Promise on every job. A live person answers, day or night.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Garland and the Dallas-Fort Worth area for over 42 years.