Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Richardson
Gate parts and welding in Richardson usually means one of three things: a hinge post has tilted on black clay, a 40-year-old weld has finally let go, or an original gate from the 1980s needs hardware that big-box stores don’t stock. We handle all three. Ironworks Gate Co. has served Richardson homeowners since 1984, and our crews know the difference between a gate that just needs a hinge and one that needs its post reset in concrete. If your gate drags, sags, or won’t latch, call (903) 627-2906 and we’ll tell you straight what it needs and what it costs before any work begins.
Why Ironworks Gate Co. Is Richardson’s Preferred Gate Parts & Welding Company
We’ve been welding and rebuilding gates in Richardson long enough to know the houses as well as the hardware. From the brick ranches along Belt Line Road to the HOA-governed streets of Canyon Creek, the pattern is consistent: original gates installed 40 or 50 years ago, built well, but now fighting the soil beneath them. Richardson homeowners keep calling us back because we diagnose the post before we touch the hinge. That’s not a slogan. It’s how you avoid paying for a new hinge, then paying again next spring when the same gate sags. A live person answers our phone 24 hours a day, seven days a week, and our uniformed, background-checked technicians arrive when we say they will. Every job, large or small, comes with our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. No paperwork, no arguing.
Our Gate Parts & Welding Services in Richardson
Hinge Replacement
We replace more gate hinges in Richardson than almost any other part, and the reason is rarely the hinge itself. Expansive clay tilts the hinge post forward, the gate drops at the latch side, and the hinge gets blamed. We press the post back to plumb or sister it, then weld on a new hinge plate that actually fits the existing gate frame. Most hinge replacements are a single-visit job, with the price settled up front.
Post Replacement
When a post is rotted through at the base or cracked by decades of soil movement, no amount of hinge adjustment will hold. We cut out the old post, set a new one below grade in a properly sized concrete footing, and let it cure before re-welding or re-bolting the gate. On Richardson’s black clay, footing depth and concrete mass matter more than anything, and we size both for the local soil, not some national average.
Rail Repair
Bottom rails on swing gates bear the brunt of the problem in Richardson: heat expands the metal, clay pushes on the posts, and eventually the rail bows or cracks at the weld points. We grind out failed welds, straighten or replace bent rail sections, and re-weld with correct penetration and a clean finish. On wooden gates, we sister additional support where HOA covenants allow it, because a repaired rail that doesn’t account for soil stress will fail again within a few seasons.
Custom Welding
Some Richardson gates need a part that no longer exists. Original ornamental iron from the 1970s with a broken scroll, a custom driveway gate wider than anything stocked today, or a latch assembly that was discontinued before the current homeowner bought the property. Our welding shop fabricates replacement sections, brackets, and latch keepers to match the existing gate rather than forcing a modern part to work. It’s craft metalwork, and it’s surprisingly affordable compared to replacing the whole gate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Richardson
Our Gate Parts & Welding team works on original equipment from every era, including operators and hardware from LiftMaster, FAAC, and Elite that were installed when Richardson’s housing stock was first built out. We keep common hinge plates, rack sections, latch assemblies, and safety parts on our service trucks, and for older or unusual hardware we can usually source and install within the same week. Trained on nine major automation brands, we won’t show up to a 1984 swing gate with parts that only fit a 2015 slide gate.
Common Gate Parts & Welding Problems We See in Richardson Homes
- Clay heave tilts the hinge post forward. Richardson’s expansive black clay swells after fall rains and contracts through the summer, slowly pitching posts out of plumb. The latch side drops an inch or more, and the gate drags even with brand-new hinges. The fix is post correction, not another hinge swap.
- Obsolete control boards fail in 100°F heat. Original 1980s gate operators still run fine in mild weather, then shut down during the long Richardson summer stretch above 100°F. Heat stress on 40-year-old circuit boards is a progressive failure, and it usually strands the gate in whatever position it died in.
- Slide gate rack and pinion binds from post movement. Years of soil-induced post movement pull the rack out of alignment with the pinion gear. The operator doesn’t know that; it just keeps pulling until it strips gear teeth. We realign the rack, set the posts, and replace the stripped pinion in one visit.
- Wood gates drop even with new hardware. Along older HOA streets in Canyon Creek and similar subdivisions, wood gates routinely sit a full inch or more low at the latch side. The hinge isn’t the failure. The hinge post tilted forward in wet clay, and until that post is reset or sistered, no amount of hinge shimming will hold for long.
Pricing for Gate Parts & Welding in Richardson, TX
In Richardson, hinge replacement on a standard swing gate typically runs $150 to $350 depending on gate weight and hinge style. Post replacement, including demolition, new footing, and resetting, lands between $450 and $900. Rail repair and custom welding generally start around $125 for small brackets and run up to $1,200 or more for extensive frame rebuilding or ornamental fabrication. If the gate needs both post and hinge work, the combined job is always cheaper when done together than separately, because the labor overlaps. We quote a fixed price before we start, and we stand by that number. You’ll know the exact cost before a single bolt is turned, and our $50 Off Any Repair Over $250 offer applies to most Richardson gate welding repairs.
We Also Serve Cities Near Richardson
Ironworks Gate Co. serves Richardson and the surrounding North Dallas communities from Addison and Carrollton to Plano and Garland. If you live just over the city line in any of those neighborhoods, the same crews, same trucks, and same written promise cover your gate work. Call us and we’ll get you scheduled.
Serving Richardson, TX - Our Local Coverage Area
We’re based in the Richardson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Richardson
Because the real problem is the post, not the hinge. Richardson’s expansive black clay tilts hinge posts forward as it cycles through wet and dry seasons. You can adjust or even replace hinges every year, but the gate will keep dropping until the post is reset in a properly sized footing. That’s why we check plumb before we touch the hardware. Call (903) 627-2906 and we’ll tell you what’s actually moving.
Usually yes, but it depends on the operator. Many 1980s-era units can be retrofitted with modern safety photocells, edge sensors, and a current control board to meet UL 325. Some cannot, and at that point replacement is the cheaper long-term answer. We’ll give you a straight answer, with a written quote, before you spend anything. Free second opinion on any written estimate.
Metal expands when it heats, and Richardson summers routinely push above 100°F for weeks at a time. The frame grows slightly, and if the gate was already tight, it binds at the latch or strike plate. This is usually a tolerance issue that can be fixed by adjusting the latch position or grinding a few thousandths of relief where it binds. It’s a quick, single-visit fix in most cases.
On Richardson’s soil, it’s the rack and pinion. As the posts shift slightly with clay movement, the rack runs out of line, the pinion gear doesn’t mesh cleanly, and eventually the teeth strip. The operator is still pulling; the gear just can’t turn the gate anymore. We realign the rack, reset the posts, and replace the pinion gear so the operator isn’t fighting the soil every time it opens.
Yes, and it’s the most common scenario we see in Canyon Creek. The hinge wasn’t the problem. The hinge post tilted forward in the wet clay, taking the gate with it. We’ll sister the post or pull it back to plumb, re-set the hinge geometry, and weld or lag everything solid. Then the gate will sit level, and it will stay level through the next wet-dry cycle. Estimates are free; call us for one.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Richardson since 1984.