Ghost Controls Gate Repair in Garland, TX

Ghost Controls Gate Repair in Garland, TX | Ironworks Gate Co.

We provide independent Ghost Controls Gate Repair in Garland, and we stock both OEM and upgraded aftermarket parts so most jobs finish in one visit. The defining difference here: Garland’s Blackland Prairie clay heaves gate posts out of alignment, and that movement strips Ghost Controls actuator gears faster than anywhere we work in the metro. If your gate is grinding, stalling, or draining batteries, call (903) 627-2906 for a straight answer and a free estimate.

Call (903) 627-2906

Why Garland Residents Choose Us for Ghost Controls Service

We’ve been at this for over 42 years, and we’ve serviced every major Ghost Controls residential operator generation in Garland, from early gate-only systems to today’s smartphone-ready kits. That’s how we know the brand’s torque limits, control board logic, and post-mount quirks better than a parts-only shop. We’re independent, which means we repair what’s actually failing instead of pushing a warranty replacement you don’t need.

Victor Salinas, our owner, grew up in Richardson and has spent the better part of three decades working on gates across the north Dallas corridor. He learned the mechanical and electrical side of the trade through the HVAC and Industrial Technology programs at Collin College, where instructors drilled into him that sloppy work on a motor is just a future emergency call waiting to happen. That’s the standard we carry into every Garland driveway. We tell you what it needs, we fix what we say we will, and we don’t disappear after the invoice.

Common Ghost Controls Gate Repair Problems We Solve in Garland

• Post-heave torque on swing arms: Garland clay swells after wet seasons and shifts posts, bending Ghost Controls actuator arms and stripping their resin gear teeth. We see this every single spring after the rains push through. The arm still extends, but the gear inside is chewing itself up.
• Control board corrosion: North Texas humidity plus condensation inside Ghost Controls weatherproof boxes leads to MOSFET failures, especially on older AXDP boards. The box says weatherproof, but a Garland humidity cycle can still find its way in, and once moisture reaches the board, the gate starts acting possessed.
• Limit switch drift after freeze-thaw: The 2021 ice storm cracked welded limit brackets and knocked alignment off on many Ghost Controls swing operators. Gates that previously opened to full travel started stopping mid-swing afterward. We still find these misalignments when homeowners finally investigate the stop-and-reverse behavior.
• Battery drain from photocell misalignment: Tilted posts on 40-year-old Garland fences make Ghost Controls safety eyes misalign, so the system cycles repeatedly and kills backup batteries. The gate looks dead, but the real problem is two misaligned sensors on posts that haven’t been level for a decade.
• Stripped resin gears from repeated strain: The Ghost Controls linear actuator uses a resin gear that’s strong but not indestructible. When a Garland gate post has heaved even an inch out of plumb, that gear absorbs constant load and eventually strips. Replacing the gear without fixing the post just sets up the same failure for next season.

Ghost Controls Service in Garland: What Local Conditions Mean for Your Equipment

Garland’s Blackland Prairie clay moves water unevenly under a single gate. The hinge-side post can be dry-packed while the latch-side post sits in a wet seam, heaving one post 2 to 3 inches higher and creating what locals call a ‘walking gate’ - a visible diagonal sag most people blame on old hinges. Ghost Controls swing arms hide this differential because their linear actuators still operate through the tilt, so the first visible symptom is often a stripped gear or a bent arm, not a dragging gate. We always check post differential with a 4-foot level before replacing any Ghost Controls part. In established south and central Garland neighborhoods where homes were built in the 1970s and 1980s, this one check saves homeowners from paying for a gear repair that fails again in six months. Realigning without re-setting the post just delays the return call by a season.

Ghost Controls Models & Products We Service in Garland

Our team covers the full Ghost Controls residential line, including the TSS1 automatic gate opener kit, AXDP dual swing gate opener, LSM1 sliding gate opener, and REX1 residential keypad and remote system. For most board failures and keypad issues, we stock OEM Ghost Controls parts and can complete the repair same visit. For post-heave damage, we replace the actuator with OEM only, because Ghost Controls’ torque curve is tuned to its own gear geometry. On older single-arm units, we often recommend a full post-reset plus new actuator rather than patching a stripped gear. Garland’s clay will re-strip a repaired gear within a season, and that’s not a repair we want to sell you twice. For broader Ghost Controls sales & service, we carry the parts and programming knowledge to handle most residential applications.

Ghost Controls Service Pricing in Garland

FAQs - Ghost Controls Gate Repair in Garland

Service Areas Near Garland

We serve Garland and the surrounding communities including Richardson, Addison, Murphy, Plano, and Far North Dallas. For customers in Richardson, you can learn more about Ghost Controls service in Richardson. For Addison specifically, see Ghost Controls service in Addison. Or view our full Garland service area page for details on response times.

Book Your Ghost Controls Service in Garland Today

You’ve got a gate that isn’t behaving, and you want it fixed without a runaround. Call (903) 627-2906 for a free estimate. A live person answers 24 hours a day, 7 days a week, and we’ll schedule your Garland repair at a time that works for you.

Written by Victor Salinas, Owner at Ironworks Gate Co., serving Garland since 1984.