Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Repair in Richardson: What to Know First
Linear gate repair in Richardson typically runs $190 to $600 depending on whether the failure is in the operator board, limit switches, or the mechanical side of the gate itself. Most Linear jobs we see are completed in a single visit, and we quote every price before a single bolt is turned. We are an independent Linear service provider here in Richardson, not a manufacturer affiliate, which means we repair what actually failed instead of pushing a full system replacement.
If you own a Linear gate opener that has stopped closing, grinds when it runs, or refuses to respond to the remote, this page tells you what is likely wrong and what it will take to make it right. Call (903) 627-2906 and a live person answers, day or night.
How Linear Products Fail - and How We Fix Them
Linear has been on Texas driveways for decades, and the operators we work on in Richardson fall into a few recognizable patterns. Here is what we actually find when we open the cover.
- Linear LDO series: capacitor failure after hard starts. The LDO50 and LDO33 swing-arm operators use a start capacitor that takes a beating in Richardson’s summer heat. When the gate hums but will not move, or trips the breaker on hot afternoons, nine times out of ten the capacitor has swollen. We replace it with a capacitor rated for higher ambient temperature than OEM, which is the fix Linear owners in north Texas need and a parts catalog will not tell you.
- Linear actuator arms: stripped limit nuts and drifted stop points. The Linear actuator arm (the motorized shaft that moves the gate leaf) relies on internal limit switches to know where open and closed are. Over thousands of cycles, the limit nuts back off and the gate starts slamming past its stop, or stopping two feet short of closed. We reset the limits and, where the threads are worn, replace the limit assembly rather than just re-tightening it so the problem does not return in three weeks.
- Linear receivers: burned-out relay contacts. Linear receivers have internal relays that click every time the gate opens. Cheap surge protection or repeated lightning-adjacent strikes in Richardson will arc the contacts until the relay welds shut or fails open. The symptom is a remote that blinks but a gate that ignores it. We replace the relay at board level rather than the whole board when possible, which routinely saves the owner two or three hundred dollars.
- Linear keypads and transmitters: failed weather seals and dead batteries disguised as radio problems. We get calls saying “the remote stopped working,” and what we find is a keypad that filled with water after a Richardson downpour, or a transmitter battery that leaked and corroded the contacts. New battery, cleaned terminals, new gasket, and the radio works like new. We always check the simple thing before ordering parts.
- Linear photoelectric sensors: misalignment and sun washout. The photo eyes that keep the gate from closing on a car will misalign when a gate sags even a quarter inch, or they’ll false-trip in the direct low-angle sun that hits west-facing Richardson driveways every afternoon. We align the sensors, shim the hinge if needed, and reposition the eyes so Texas sun does not keep the gate from closing.
Our Linear Gate Repair Process
This is how a Linear repair goes at Ironworks Gate Co., every time. No shortcuts, no surprises.
- 1
You call, a person answers. We ask what the gate is doing, what model operator you have, and when it started. We schedule a visit that works for you, including same-day for gates stuck open or closed.
- 2
On-site diagnosis. The technician tests the operator, the limit switches, the safety sensors, and the mechanical movement of the gate itself. On Linear jobs, we look at the actuator arm first, then the board, then the receiver.
- 3
Straight answer on parts. If the part is available as OEM and warranty-safe, we use it. If OEM is backordered, or if a quality aftermarket part is the better fix for Texas heat, we tell you and we quote the difference. You choose before we turn a wrench.
- 4
The repair. We perform the fix, then cycle the gate ten to fifteen times under load. We check the closing force, the limit stops, and the obstruction reverse.
- 5
Cleanup and a walkthrough. We show you what we did, what we replaced, and what to watch for. The site is left clean. The price matches the quote.
- 6
The 90-Day Done Right Promise. Every Linear repair is covered in writing. If it is not right, we come back and make it right. No paperwork, no arguing.
What Linear Gate Repair Costs in Richardson
Most Linear repairs we do in Richardson land between $190 and $600. A failed start capacitor with labor runs $190 to $240. A limit switch assembly replacement runs $280 to $380. A relay repair on a Linear receiver runs $220 to $310. A complete board replacement, when the board is genuinely beyond board-level repair, runs $450 to $600. Prices move based on the model, whether the gate is a light single leaf or a heavy estate gate, and how much of the mechanical side has drifted with age. You will have the price in writing before work starts, and we hold the $50 Off Any Repair Over $250 discount for every qualifying job without being asked. Call (903) 627-2906 for a free estimate.
Why Richardson Homeowners Call Ironworks Gate Co. for Linear Work
We have been at this for over 42 years, and a fair share of the Linear operators still running in Richardson today were installed long enough ago that the warranty has been expired for two decades. Victor Salinas grew up in the Prairie Creek neighborhood, and he has spent the better part of three decades working on gates across the north Dallas corridor, including plenty of Linear actuators and receivers. Our technicians are trained on Linear alongside eight other opener brands, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing among them, so the fix is correct on the first visit whatever is mounted on the post. Every job is covered by the 90-Day Done Right Promise in writing. A live person answers the phone at any hour. And our technicians are background-checked, uniformed, and guided by a simple rule: work in a customer’s home the way you would work in your own mother’s.
Frequently Asked Questions
No. As an independent Linear service provider in Richardson, we never void a warranty by performing a repair. If your Linear operator is still under an active manufacturer warranty, we can work with that process and use OEM parts where required, though most of the Linear openers we see in Richardson aged out of warranty years ago.
We can usually get a technician to your Richardson home the same day for a gate stuck open or closed, and most Linear repairs are completed in a single visit. If a specific part has to be ordered, we tell you before we leave and we quote the full job so there are no surprises when we return. Call (903) 627-2906 to check today’s schedule.
We tell you what it needs, we fix what we say we will, and we don’t disappear after the invoice. If the operator board, actuator, and receiver are all failing and the gate itself is rusted through, we will say so. But if a single component is the culprit, we repair that component. We do not push full replacements they push margins, not gate problems.
Most common Linear parts, capacitors, limit assemblies, relays, sensors, and transmitters, are available locally or within a day or two across the Dallas metro. We keep common failure parts on the truck so the repair happens the first time we visit.
If your Linear gate is acting up and you want a straight answer, call (903) 627-2906 now. A live person answers 24 hours a day, 7 days a week, and the estimate is free.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Richardson and nearby areas.