FAAC Gate Installation Nationwide

FAAC Gate Installation in Richardson: What to Know First

FAAC gate installation in Richardson typically takes one full day for a standard driveway swing or slide gate when the concrete pad and power are already in place. As an independent FAAC service provider, we install and set up the complete range of FAAC operators, from the 390 and 400 series for lighter residential gates up to the 770 and 844 hydraulic lines found on heavier estate entrances, and our pricing is settled in writing before we touch a wrench. This page is for Richardson homeowners who bought a FAAC opener, or are considering one, and want the installation done right the first time.

Call (903) 627-2906

If you have questions that aren’t answered here, call us at (903) 627-2906. A live person answers. Every call, every time.

Key takeaways:

• We install FAAC operators on new gates and retrofit them onto existing ones.
• Every FAAC installation is covered by our written 90-Day Done Right Promise.
• Upfront pricing agreed before work starts; no surprises on the bill.
• We service all nine major opener brands, so if your gate has a FAAC motor and a LiftMaster keypad, we handle both in one trip.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But every brand has its habits, and after years of working on these units across Richardson, we know where they tend to give out and what to do about it when we’re installing the new one.

• 390 and 400 series control boards and capacitor fatigue: These light-duty residential operators run well for years, but the capacitor is usually the first component to call it quits. When the gate moves slowly and then stops entirely, a failed capacitor is the usual culprit. We bench-test the board before removing anything, and we replace capacitors with the correct microfarad rating for the motor, never a generic part with “close enough” numbers.
• C720 and C721 hydraulic operators and cold-weather stiffness: In Richardson we don’t get ice storms often, but we get cold snaps, and hydraulic fluid thickens in January. Homeowners call in February thinking the operator died, when the real issue is degraded hydraulic fluid combined with a gate that’s slightly out of balance. We change the fluid to the correct spec, set the pressure relief valves properly, and the gate moves like it should.
• 770 and 844 series and repeated thermal overload trips: These are the heavy-duty lines, and when the thermal limiter keeps kicking the operator off, we look at the gate itself before blaming the motor. A gate that’s been re-welded a few times over the decades carries extra weight. The operator trips because it’s working harder than it should. We check the load, check the duty cycle against the gate’s actual weight and cycle count, and set the limits so the motor isn’t running past where the gate stops.
• Photocell alignment drift on all series: The safety eyes get knocked out of alignment by wind, by lawn equipment, by kids, by the gate itself shifting on its hinges. FAAC’s control logic refuses to close when it doesn’t get a clear signal, so a misaligned photo eye usually shows up as “the gate opens but won’t close.” We align the eyes, shim the brackets so they stay put, and verify the beam reads clean before we call the installation done.
• Undersized wire from a previous installation: This one isn’t FAAC’s fault, but we see it on older Richardson homes where a handyman or a previous owner ran 16-gauge wire out to the operator because it was cheaper. Low voltage at the board causes erratic behavior: the gate stops mid-cycle, the remote range drops, or the control board resets. On installation we pull new wire to the correct gauge for the operator and the run length, because no amount of new hardware fixes a thin wire buried in the yard.

Our FAAC Gate Installation Process

1. 1
   You call, we answer. A live person takes your call at (903) 627-2906, asks about your gate and your existing FAAC equipment, and we schedule a visit. We’ll be there when we say.
2. 2
   On-site assessment. We inspect the gate, the existing operator if there is one, the power supply, the mounting points, and the hinges or rollers. We measure the gate’s weight and dimensions. We tell you what it needs, what can wait, and what it’ll cost. The price is settled before any work starts.
3. 3
   Parts decision. For FAAC equipment, we recommend genuine FAAC parts for anything that touches safety or the control board. For non-critical items like brackets or hardware we may offer a quality aftermarket option if it saves you money without cutting corners. We explain the difference before we spend your money.
4. 4
   The installation. We set the operator, run or verify the power, connect the controls, and program the open and close limits. On slide gates we check the rack and pinion engagement. On swing gates we check the leaf geometry and the travel arc so the motor isn’t fighting the gate.
5. 5
   Safety verification. We test the photocells, the force settings, and the auto-reverse on both directions. We check for pinch points and make sure the gate doesn’t stall at any point in its travel.
6. 6
   The walkthrough and the Promise. We show you how the unit works, answer your questions, and leave the job site cleaner than we found it. Then we hand you the written 90-Day Done Right Promise. If anything isn’t right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Installation Costs in Richardson

Installation pricing depends on the operator model, the gate’s weight and type, and what’s already in the ground. Here’s what we typically see in Richardson:

• FAAC 390 or 400 swing gate installation: $950 to $1,800, assuming the gate is in good condition and power is at the site.
• FAAC 770 or 844 heavy-duty operator installation: $2,200 to $4,500, depending on gate weight and whether hydraulic or electromechanical.
• Full gate replacement plus FAAC automation: $5,000 to $12,000 for a custom welded steel driveway gate, new posts, and FAAC automation.
• Retrofit: new FAAC operator onto an existing gate: $800 to $1,600 if the gate itself is sound and we’re not rebuilding the structure.

What moves the price: the gate’s true weight and balance, the distance from the electrical panel to the operator, whether we’re pulling new wire, and whether the existing mounting points can be reused or need to be re-welded. Every installation quote is free and fixed in writing before work begins. Call (903) 627-2906 for a number on your specific gate.

Why Richardson Homeowners Call Ironworks Gate Co. for FAAC Work

Victor Salinas learned the electrical side of this trade at Collin College and has spent the better part of three decades working on gates across the north Dallas corridor. The company has been serving Richardson since 1984, and we plan to be here for another forty years. When we install a FAAC operator on your gate, we’re not running out the door at the end of the day hoping it holds.

We guarantee the work in writing with the 90-Day Done Right Promise. We answer the phone 24 hours a day, 7 days a week. And because we’re trained on nine opener brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, we can handle whatever your gate has on it, even if the last installer mixed brands. We tell you what it needs, we fix what we say we will, and we don’t disappear after the invoice.

Homeowners between 55 and 75 don’t want to chase a contractor. They want the job done once. That’s how we’ve earned our reputation: the quiet way, one gate at a time.

FAQs