Ghost Controls Welding & Fabrication Nationwide

Ghost Controls Welding & Fabrication: The Richardson Owner’s Guide

We stock, weld, and install Ghost Controls-compatible gate components across Richardson, with most welded bracket repairs and hinge fabrication running $220 to $480 installed, depending on the part and the gate’s weight. Most jobs are completed same-day when the gate isn’t holding a load safely, and we always confirm the price before the first weld is struck.

Call (903) 627-2906

Here’s how it usually goes: the gate starts dragging on one corner, or you hear a clunk when the opener cycles. The arm isn’t loose at the operator, it’s loose where the metal meets the gate. That’s the moment a homeowner realizes welding isn’t a metaphor. It’s the actual fix.

Ghost Controls builds a good kit for a fair price. What fails first in Texas isn’t the board or the motor. It’s the metal around the mounting points, and it fails because our soil shifts and our sun bakes, not because the kit was bad. We’ve been welding and fabricating gate hardware in Richardson for over 42 years, and we can tell you exactly what your gate needs in about ten minutes of looking.

Key Takeaways:

• We stock Ghost Controls-compatible brackets, receiver plates, and arm extensions on our trucks
• Installed welding and fabrication work in Richardson typically runs $220 to $480
• Most bracket and hinge jobs are finished same-day, in a single visit
• Every job is covered by our written 90-Day Done Right Promise
• Call (903) 627-2906 and a live person answers, day or night

Which Ghost Controls Models This Applies To

The welding and fabrication work we do applies to every Ghost Controls opener and gate configuration we see in Richardson, but the specifics change by series. The AXDP and AXD heavy-duty arms use a larger mounting clevis than the standard residential kits, which matters when you’re ordering a replacement bracket. The TSS1 and TDS2 solar kits often get paired with lighter tube-steel gates, and those thinner posts are exactly where we see metal fatigue first.

Ghost Controls marks their arms with a model label near the motor housing, but years of Texas sun can fade that label to nothing. When it’s gone, we measure the arm barrel and the clevis width to match the correct piece. If you don’t know your model, don’t guess. A bracket for an AXD won’t fit an AXX arm, and forcing it just ruins both.

As for OEM versus quality aftermarket: honest answer, for Ghost Controls brackets and receiver plates, a well-made aftermarket piece at a heavier gauge than the factory original is often a better long-term call, especially on heavy gates. The factory brackets are adequate. The Texas wind and shifting clay soil in Richardson are not always polite. We’ll tell you what it needs, and we’ll explain why before any metal is ordered.

We’re an independent service provider, not affiliated with Ghost Controls, and we carry or can fabricate parts for Ghost Controls along with LiftMaster, Mighty Mule, and DoorKing systems.

Signs Your Ghost Controls Welding & Fabrication Is Failing

• The gate sags toward the latch post. The hinge welds on the post side are stretching. The gate still opens, but the weight is pulling the heels out of the weldment. In Richardson’s clay soil, even a well-set post can lean half an inch in a wet spring, and that lean comes out of the welds first.
• The opener arm clunks when it starts and stops. The clevis pin hole in the bracket has wallowed out over thousands of cycles. The arm now has slack before the gate moves. Every clunk is the pin slamming the edges of an oval hole that used to be round.
• You see rust streaks running down from the hinge barrels. The zinc is gone and the steel is bleeding. It doesn’t mean the gate is dead, but it means the metal is thinning where the force concentrates. We’ve replaced hinges in Richardson that were down to a quarter of their original thickness.
• The gate scrapes the driveway on one side. The hinge alignment is off, which means the welds have moved or the post has shifted. Shimming the opener won’t fix it. The correction is re-welding the hinge points true.
• The receiver plate flexes when the arm extends. The plate was welded on the diagonal at only two points, and those two points are now working back and forth like a hinge. Operator cycle times increase, safety edges trip, and the arm eventually tears the plate off entirely.

Replacement Cost & What’s Included

For most Ghost Controls welding and fabrication work in Richardson, you’re looking at $220 to $480 installed. A heavy receiver plate fabrication with gusseting and reinforcement runs toward the top of that range. A simple bracket swap with fresh weld beads stays at the bottom. The biggest cost driver is gate weight and access to the hinge side, not the price of the steel.

Every quote is parts and labor together, confirmed in writing before we touch the gate. You’ll know the number that applies to your job before the welder fires up. If we find something else while we’re in there, we stop and show you before adding a dollar.

All welded work carries our written 90-Day Done Right Promise. If the weld fails or the bracket moves within 90 days, we come back and make it right. No paperwork, no arguing. That’s the Keystone Standard we’ve put on every job for over four decades.

Ghost Controls Welding & Fabrication Cost in Richardson, TX:

• Simple bracket replacement (single clevis, standard arm): $220 - $280
• Heavy-duty receiver plate fabrication and weld (AXD/TSS series): $320 - $420
• Full hinge re-weld and alignment (both hinges, post side): $380 - $480
• Custom arm extension or post reinforcement: $350 - $450
• $50 Off Any Repair Over $250 (standing offer)
• 5% Senior and Veteran discount, always

DIY or Call Us?

The honest split is this: you can check the bracket bolts for tightness, and you can look for the rust streaks and wallowed holes described above. You can also make sure the gate is properly counterbalanced so the opener isn’t doing the work of the hinge. That’s diagnosis, and it’s safe.

What you shouldn’t do is weld a gate that’s holding torque. A gate under load can shift when a weld releases, and a pinch point at the hinge line will remove fingers. We don’t say that to scare anyone off. We say it because it’s true, and because a proper weld on structural gate hardware needs the gate blocked, the load taken off, and the right rod for the metal thickness. That’s not a flap-disc and a hardware-store welder job.

If you’d rather watch us do it than fight it yourself, call (903) 627-2906. We’ll give you a straight price and a time we’ll be there, and then we’ll actually be there.

FAQs

Call Ironworks Gate Co. for Ghost Controls Welding & Fabrication in Richardson

If your Ghost Controls gate is dragging, clunking, or leaning, we’ll tell you what it needs, we’ll fix what we say we will, and we don’t disappear after the invoice. We’re Victor Salinas and the team at Ironworks Gate Co., and we’ve been welding and fabricating gates in Richardson and across the north Dallas corridor for over 42 years. A live person answers the phone 24 hours a day, seven days a week. Call (903) 627-2906 for a free estimate, and we’ll settle the price before a single weld is struck.

Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Richardson and nearby areas.