FAAC Gate Repair Nationwide

FAAC Gate Repair in Richardson: What to Know First

FAAC gate repair in Richardson typically runs between $180 and $550 depending on what failed, and most jobs are completed in a single visit. We’re an independent FAAC service provider, which means we answer to you, not to a manufacturer’s warranty department. If your FAAC operator is clicking but not moving, blowing fuses, or the gate has started drifting off its hinges, this page will tell you what’s actually going on and what it costs to make it right.

Call (903) 627-2906

This page is for Richardson homeowners with FAAC swing or slide gate operators, whether it’s a 390, 400, 750, 770, or an older model that’s been running since the house was built. Call (903) 627-2906 and a live person answers, day or night. Ask for Victor.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But everything with moving parts eventually wears, and FAAC units have predictable failure points we see across Richardson driveways week after week.

• The 750 and 770 series capacitor failures. These slide gate operators use a start capacitor to get the motor moving. North Texas heat cooks them. When a capacitor goes weak, the gate starts moving slower, then refuses to start without a push. We keep correct microfarad-rated capacitors on the truck and swap them on the first visit. A weak capacitor can also take out the motor windings if ignored long enough, so we always test the draw on the motor while we’re in there.
• 390 and 400 series limit switch drift. These swing gate operators rely on mechanical limit switches to tell the arm where to stop. Over years of use, the cams inside wear and slip, which is why a gate will start slamming past its normal stop or stopping six inches short. We reset and, when needed, replace the limit switch assembly and re-learn travel limits per FAAC’s procedure. It’s a 45-minute repair on most models.
• Hydraulic 770 pump motor seal leaks. The FAAC 770 series uses a hydraulic pump rather than a direct-drive motor. Richardson’s freeze-thaw cycles in January and February push the seals to their limit, and when one starts weeping, you’ll see oily residue on the pump body and the gate will labor to open. We replace seals and top off with the correct hydraulic fluid rather than just wiping the mess and calling it fixed.
• Control board failures from power surges. Richardson sits in a storm corridor, and FAAC boards are sensitive to surges even with a surge protector on the line. The symptom is usually a dead keypad or a board that clicks but won’t run the motor. Before blaming the board, we ring out the motor, capacitor, and transformer so you’re not paying for a board when a $28 relay was the real problem. If the board is gone, we install a genuine FAAC replacement so all factory settings and safety inputs work exactly as designed.
• Photocell and safety edge faults on older C720 and C721 systems. These were workhorses, but their safety sensors are now over 15 years old in most Richardson homes. Dust, spider webs, and Texas sun degrade the lens and wiring. The gate will refuse to close or reverse mid-cycle for no obvious reason. We clean, align, and test the full safety circuit, and replace failing photocells with current FAAC-compatible units rather than jumping them out. A jumped safety edge is a lawsuit waiting to happen.

Our FAAC Gate Repair Process

Every FAAC job starts the same way: we listen, then we look. Here’s how a typical repair goes from call to cleanup.

1. 1
   You call, we answer. A live person, 24 hours a day. We’ll ask what the gate is doing or not doing, what model operator you have if you know it, and whether it’s a swing or slide gate.
2. 2
   We arrive and test. Before touching a bolt, we run the gate through its cycle to see the failure in person. We check voltage at the operator, amp draw on the motor, and the condition of the hinges, posts, and chain or piston.
3. 3
   We tell you what it needs. We explain the problem plainly, show you what’s failed, and give you a written price before any work starts. If it can wait, we say so. If it’s urgent, we say that too.
4. 4
   Parts decision, made together. For FAAC boards and capacitors, we recommend genuine FAAC parts. For wear items like hinges, chains, and some sensors, we may recommend a quality aftermarket option that costs less and lasts just as long. You decide, with our honest take.
5. 5
   The repair and the test. We complete the work, then run the gate through a minimum of five full open-close cycles. We check safety edges, force settings, and the close delay. If it’s not right, we stay until it is.
6. 6
   Cleanup and the guarantee. We leave the site cleaner than we found it, walk you through what was done, and every job is covered by our written 90-Day Done Right Promise.

What FAAC Gate Repair Costs in Richardson

Here’s what Richardson homeowners can expect to pay for common FAAC repairs. These are real ranges, not estimates pulled from a national chart.

• Capacitor replacement: $180-$260
• Limit switch reset or replacement: $210-$340
• Photocell or safety edge repair: $190-$320
• Control board replacement (genuine FAAC): $350-$550
• Hydraulic seal replacement on 770 series: $280-$440
• Full hinge and post repair: $300-$800 depending on steel work required

The price moves based on the model, whether we’re replacing a board versus a wear part, and how much welding or fabrication the job needs. What never changes: the price is agreed before we start, in writing, and it will not change when the invoice arrives. Call (903) 627-2906 and we’ll give you a free estimate over the phone, or come out and confirm it in person.

Why Richardson Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been fixing gates in Richardson since before FAAC operators were common on North Texas driveways. Our technicians train on nine opener brands, so when we’re on a FAAC job we know that board’s logic, and we also know when a LiftMaster retrofit is more cost-effective than pouring more money into a 20-year-old FAAC that’s reached the end of its service life. We work on Mighty Mule, Ghost Controls, and DoorKing as well, but FAAC is what we see most often on the larger estates and newer slide gates in the area.

Every job, from a capacitor swap to a full operator replacement, is protected by our written 90-Day Done Right Promise. If it isn’t right, we come back and make it right. No paperwork, no debate. We’ve been doing this since 1984, and Victor Salinas plans to keep answering the phone in Richardson for another forty years. We tell you what it needs, we fix what we say we will, and we don’t disappear after the invoice.

FAQs